Bench notes · EV · Safety
Is your power point cooking? Granny chargers and GPO heat
A granny charger running at 2.4 kW draws 10 A, the full rating of a standard Australian 10 A power point (GPO), for 8 to 20+ hours at a stretch. Almost nothing else in the house does that. A kettle pulls 10 A for three minutes; a heater cycles on and off. An EV charge holds the GPO, its plug and its wiring at their limit all night, every night.
That is fine when everything is in good condition. When it isn't, the weak point slowly cooks. The good news is that the warning signs show up as heat long before anything melts, and heat is easy and cheap to measure.
This post explains why GPOs heat up under granny-charger loads, what the warning signs are, and how a sensor that costs about A$30 can watch the outlet for you. The full build is free in the AP Design Labs Free Library.
Why GPOs heat up
A GPO gets hot because current flows through resistance, and the heat goes up with the square of the current:
P = I² × R
At 10 A, every 0.01 Ω of extra resistance makes 1 W of heat at that spot. A healthy plug-to-socket contact is a few milliohms, so it runs barely warm. A worn or loose contact at 0.1 Ω makes 10 W, concentrated in a point the size of a grain of rice and wrapped in plastic. That is roughly a small soldering iron buried inside your power point.
It also feeds itself. Heat oxidises the brass and relaxes the spring tension in the socket contacts. That raises the resistance, which makes more heat. A connection can degrade a little more each night for weeks before anything visibly fails.
| Cause | What goes wrong | Typical clue |
|---|---|---|
| Worn socket contacts | Years of plugging in relax the spring clips, so the pins touch on a smaller area | Plug feels loose or droops |
| Plug pulled part-way out | The weight of the charger brick or cable levers the plug, so only the pin tips make contact | Charger box hanging from the plug |
| Loose terminal screws behind the faceplate | The wire termination itself becomes the hot spot | Faceplate warm around the screws even where the plug is cool |
| Oxidised or dirty pins | Corrosion film adds resistance; common in damp garages and carports | Dull or discoloured pins |
| Poor-quality plug or socket | Thin brass and weak clips have less margin at 10 A continuous | Budget outlet or a non-original charger lead |
| Extension leads, double adaptors, power boards | Every extra joint is another possible hot spot, often with thinner conductors | Anything between the charger and the wall |
| Worn GPO switch | The switch contacts carry the full 10 A too | Heat on the switch side of the faceplate |
| Hot surroundings | A sun-facing wall or a 40 °C garage leaves less headroom before parts soften | Problems mostly on summer nights |
A bad connection still only draws 10 A, so the breaker sees a normal load and the RCD sees no leakage. Heat is the only symptom, which is why it is worth measuring.
EV owners report exactly this pattern. One SolarQuotes commenter described contacts overheating at a continuous 10 A, partly because the plug was slightly extracting under the weight of the lead. The City of Unley's EV fact sheet also warns that regular charging from a standard power point can heat-damage the socket and plug.
Warning signs to look for
If you see any of these, stop charging from that outlet and have a licensed electrician check it:
- The plug or faceplate is too hot to keep your hand on comfortably
- Brown or yellow discolouration around the pin holes, or a softened or deformed plug
- A hot-plastic or "fishy" smell near the outlet (overheating electrical plastics often smell fishy)
- Crackling, buzzing or flickering at the outlet
- The plug is loose, droops, or falls out easily
- Your charger keeps cutting back its current or stopping with a fault. Many portable chargers have a temperature sensor in the plug; if it keeps tripping, believe it
The problem with these signs is that they show up late, and usually in the middle of the night when nobody is in the garage. A sensor doesn't sleep.
A simple way to measure it
The AP Design Labs GPO Temperature Monitor uses an ESP32 and two DS18B20 digital temperature sensors, programmed in MicroPython with Thonny. Nothing is opened, wired into, or attached to the mains:
- GPO sensor: taped to the outside of the faceplate, right beside the plug the charger uses
- Ambient sensor: about 30 cm away, measuring the air in the garage
- ESP32: works out how much hotter the GPO is than the room, sounds a buzzer and flashes an LED if it climbs too far, and shows live readings on a web page you can open on your phone
The DS18B20 is a good fit: it reads from −55 °C to +125 °C, is accurate to ±0.5 °C between −10 °C and 85 °C, and several sensors can share one data wire because each has its own 64-bit address.
Why measure the rise rather than just the temperature? A faceplate at 38 °C means nothing on a 36 °C Adelaide night, but a lot on a 12 °C winter night. Comparing against the room removes the weather from the reading.
One honest limitation: the sensor reads the faceplate surface, not the brass contacts inside. The inside will always be hotter than the reading, and it reacts a little slower. That is why the alarm levels below are deliberately conservative.
Free library
GPO temperature monitor for EV granny chargers
The full build: parts list, wiring, a safe mounting guide, and the complete MicroPython code for Thonny.
What the readings mean
These are the levels the monitor uses by default. They are AP Design Labs' conservative rules of thumb for a surface reading, not values from an Australian Standard, and you can change them in the code.
| Faceplate rise above room | Level | What it means | What to do |
|---|---|---|---|
| Under 10 °C | OK | Normal for 10 A continuous | Nothing |
| 10–20 °C | Watch | Warmer than ideal | Check the plug is fully home, nothing is levering it, no adaptors; keep an eye on the trend |
| 20–30 °C | Warning | Something is adding resistance | Stop using this outlet for charging; book an electrician |
| Over 30 °C, or faceplate over 60 °C | Alarm | Active overheating | Stop the charge from the car or app, switch off at the GPO, then unplug once safe; don't use it again until inspected |
The trend matters as much as the number. A GPO that ran 6 °C above the room last month and runs 14 °C above it now is degrading, even though it is still only at Watch. The monitor's web page shows the highest reading since start-up so you can spot this.
Better long-term options
A monitor tells you when there is a problem; it doesn't fix the cause. If you charge from a GPO regularly, talk to a licensed electrician about:
- A dedicated circuit and outlet for the car. Victoria's charging guide notes the Electric Vehicle Council recommends a dedicated circuit for your vehicle, and Renew's EVSE guide says even a portable charger should have its own dedicated circuit and socket.
- A heavy-duty or industrial-style outlet with stronger contacts and a locking ring, which also stops the plug being levered out.
- A 15 A outlet with a 15 A portable charger, which charges faster and runs the outlet below its limit.
- A hardwired wallbox, with the granny charger kept as the travel backup.
- A check-up of your existing GPO: terminals tightened and worn outlets replaced. It costs little compared with a melted outlet.
And always: no extension leads, double adaptors or power boards between the charger and the wall.
This monitor is an early-warning aid, not a safety device or a substitute for an electrical inspection. Never open a GPO or work on fixed wiring yourself. In Australia that work must be done by a licensed electrician.